Does your FDM/FFF print show webs of stringing, lifted corners or a suddenly shifted layer? Start with the visible symptom and test one hypothesis at a time. Changing five slicer settings together hides the cause. This hub takes you from observation to a targeted first action.

Identify the symptom and change one variable per test.

Diagnose in a fixed order

First confirm the correct filament profile, a freely turning spool and dry material. Then inspect the first layer: the correct clean build plate, even adhesion, no grease or dust. Next check nozzle and bed temperature, cooling and enclosure. Only then assess flow, nozzle, extruder, speed and acceleration. Inspect mechanics – belts, pulleys, axes and obstructions – before fine-tuning retraction, seam, support or dimensional compensation.

Changing several settings at once is the quickest way to make diagnosis harder. You will not know which change helped and may mask one defect with another. Treat the print like a technical fault: observe the symptom, form one hypothesis, change one variable and test again.

  1. Filament: is the material profile correct, is the filament dry and does the spool unwind freely?
  2. First layer: is the plate clean, correctly installed and adhering evenly?
  3. Temperature: do nozzle and bed temperatures suit the material, speed and manufacturer's guidance?
  4. Cooling: does the part-cooling fan behave as intended, and is the enclosure appropriate?
  5. Extrusion: are Flow Ratio, nozzle and extruder free of obvious problems?
  6. Speed and acceleration: does the fault appear only on fast sections or direction changes?
  7. Mechanics: are belts, pulleys, axes, fans, hotend and build plate physically sound?
  8. Slicer strategy: only now adjust retraction, seam, bridges, supports or compensation.

Use a small test model that reproduces the symptom: two towers for stringing, a flat patch for the first layer, or a fit test for dimensions. Record filament, drying state, nozzle, layer height, temperature, Flow Ratio, Flow Dynamics/K and MVS. A test log with date, one change, result and photo prevents a working profile from becoming a mystery later.

A full one-hour Benchy is unnecessary for many diagnoses. A calibration block with holes and pins is useful for dimensions. Decide when to stop refining: no print is perfect in every respect. More speed, a smoother surface, maximum strength, minimal material and short print time can pull in opposite directions. A functional bracket can show layer lines; a display model can print more slowly for appearance.

First layer, bed adhesion and warping

Loose round lines with little contact often indicate an effectively high nozzle or wrong plate type. Ridges and piled-up plastic may indicate too little gap or excessive flow. If one corner lifts, clean the plate, check local drafts and only then try a brim. If the print first sticks but later detaches, inspect shrinkage, bed temperature and material strategy.

The first layer is the foundation of the whole print. More infill or another seam setting cannot rescue a layer that never adhered evenly. Automatic bed compensation cannot calibrate away grease, dust, a wrong plate-type setting or a damaged surface.

Symptom Likely cause First action
Loose round lines with little contact Effective nozzle gap too large or wrong plate setting. Clean the plate, check its type and reassess the first layer.
Ridges and piled-up plastic Nozzle effectively too close or too much flow. Inspect plate, nozzle and first-layer behaviour; correct only if persistent.
One corner lifts Contamination, a local draft or thermal shrinkage. Clean thoroughly, avoid drafts and test a brim if needed.
Print sticks initially but detaches later Material shrinkage or insufficient bed temperature. Reassess bed temperature and material strategy.

Warping is shrinkage stress during cooling. For PLA, start with plate cleaning, first layer and drafts; for PETG, large surfaces and cooling also matter. ABS/ASA often need a stable warm enclosure. On large flat models, rounded corners, mouse ears, a brim or different orientation may help more than extra glue. Glue can act as a release layer on some plates; follow your plate and material guidance.

Plastic is deposited hot and contracts while cooling. On a large part, stress can pull corners off the plate or even distort layers. PETG usually adheres strongly, so warping there more often points to large surface area, drafts or strong cooling. ABS and ASA shrink more and benefit from a stable enclosure temperature. For PLA, extreme bed temperature is rarely the best first intervention. Extra glue is not universal: on some plates it acts mainly as a release layer.

Stringing, blobs and seams

Stringing is material leaking from the nozzle during travel. Dry the filament according to its guidance and test a suitable nozzle temperature first. Adjust retraction, wipe or travel only afterwards. PETG and TPU string more readily than PLA; extreme retraction is not a sound default, especially with direct drive.

Check Why What to do
Wet filament Moisture destabilises extrusion and can increase oozing. Dry according to the material guidance.
Nozzle temperature Excessive heat lets plastic flow out more easily. Test small reductions without losing layer bonding.
Travel and retraction Long exposed travel moves make strings visible. Tune retraction only after moisture and temperature are right.
Filament type PETG and TPU string more easily than PLA. Accept realistic limits and optimise per material.

Adding a lot of retraction immediately is a common mistake. On a direct-drive extruder, large pullback moves can make the print less stable instead.

A blob or zit on a consistent vertical line is often a seam effect. Compare its location with the seam in slicer Preview. Check Flow Ratio and Flow Dynamics/pressure advance before adding exotic wipe or coasting strategies. Random bumps can also come from moisture, oozing or plastic stuck to the nozzle. Multicolour prints add purge and nozzle-cleaning checks.

A small protrusion can sit exactly where a perimeter starts or stops. If its pattern matches the seam in the slicer, it is not a random extrusion fault. A blob repeatedly appearing at the same geometric point may also come from the toolpath or a brief pause. With many travels or multicolour work, verify that purge, retract and nozzle cleaning are consistent.

Under- and over-extrusion

Gaps between lines, thin walls or matte, interrupted tracks suggest under-extrusion. Causes include low temperature, excessive volumetric demand, a partial nozzle clog, extruder slip, wet filament or low Flow Ratio. Raised top surfaces, thick walls and poor fit suggest over-extrusion; check flow and filament profile. If the problem comes and goes, inspect spool resistance, partial clogs and heat issues.

Problem Signs Possible causes
Under-extrusion Gaps, thin walls, weak infill and matte or broken lines. Low temperature, high volumetric demand, clog, extruder slip, wet material or low Flow Ratio.
Over-extrusion Raised top surface, thick walls, poor fit and rough corners. High Flow Ratio, incorrect filament profile or unsuitable pressure advance.
Intermittent extrusion Alternating gaps and thick areas. Spool resistance, partial clog, heat issue, filament diameter variation or moisture.

MVS is not Flow Ratio. The hotend must melt enough plastic each second. If a model prints well slowly but develops gaps or matte bands at speed, test Maximum Volumetric Speed in the filament profile first. Do not increase Flow Ratio to hide insufficient melt capacity. The calibration guide gives a safe sequence.

The relevant load is volumetric flow in mm³/s, not just linear speed in mm/s. When the material-and-hotend combination cannot melt the requested quantity in time, actual extrusion drops and surfaces become weak or matte. Raising Flow Ratio cannot remove that physical melting limit.

Ringing, VFA and layer shifts

Ringing or ghosting is a repeating echo after sharp corners. Check loose belts, pulleys, frame and bearings, then acceleration; input shaping cannot repair a mechanical defect. VFA are finer vertical patterns that need not follow corners and can change noticeably with movement speed.

The printer and frame have mass and elasticity. High acceleration can excite mechanical resonances, producing echoes after a sudden direction change. Vertical Fine Artifacts (VFA) are more closely tied to motion frequency and motor/belt interaction. A modest speed change may affect VFA more than lower acceleration; VFA need not follow a corner.

An abrupt X/Y displacement is a layer shift: inspect a moving build plate, toolhead or cable obstructions, belts and pulleys, unusual noises and a curled-up print striking the nozzle. Lowering speed or acceleration is a test, not a substitute for fixing the physical cause.

A layer shift is a missed or incorrect movement, not an ordinary cosmetic setting. Check that the build plate cannot move, belts are correctly tensioned and pulleys are secure, and cables or the toolhead do not hit anything. A curled-up portion of the print may strike the nozzle. On a CoreXY machine, inspect the toolhead's full movement path.

Bridges, overhangs, supports and layer bonding

A bridge spans two supports and needs suitable cooling, temperature, bridge flow and speed. An overhang rests partly on the previous layer; layer height, line width, cooling, temperature and orientation act together. With support, a large Z gap removes easily but leaves a rough underside; a gap that is too small may weld to the model. A dense interface may help. Sometimes reorienting, splitting the model or designing chamfers around 45 degrees is better.

Bridges

The first bridge lines literally have air underneath. They must span from one support point to another without breaking. That calls for enough cooling, controlled temperature, suitable bridge flow and a speed that keeps the line taut.

Overhangs

Only part of each new overhang line rests on the previous layer. As the angle grows, support diminishes. Layer height, line width, cooling, temperature and model orientation jointly define the limit.

Supports and design

  • A large Z gap makes support easy to remove but leaves a rough or sagging underside.
  • A small Z gap gives better support but can weld support to the model.
  • A dense support interface can improve the underside without making every support solid.
  • Another orientation can eliminate support and improve strength at the same time.

If a model requires enormous amounts of support, revisit the design. Chamfers of about 45 degrees, splitting the part and thoughtful fillets may work better than slicer compensation.

Weak layer bonding can result from low temperature, too much cooling, high speed or excessive layer height. For functional parts, orientation often matters more than a few extra percent of infill. See also why a 3D print is strong or weak.

FDM prints are anisotropic: strength within a layer differs from strength between layers. Low nozzle temperature, too much cooling or excessive speed can weaken interlayer bonding. For a functional part, first examine its orientation relative to the applied load before simply raising infill.

Bands, dimensions, moisture and nozzle

Not every horizontal band is a mechanical Z problem. Check whether spacing is periodic and repeats on other models; temperature, filament, speed changes and geometry can also create bands. Correct dimensions specifically: only wide first layers call for first-layer work or elephant foot compensation; small holes call for hole compensation or CAD tolerance; outer contours call for contour compensation after calibration. Do not scale the entire model if only one feature type is wrong.

Dimensional error Prefer Not the first choice
Only first layers are too wide. First-layer correction or elephant foot compensation. Scaling the entire model.
Holes are consistently too small. Hole compensation or CAD tolerance. Lowering flow for the whole model.
Outer contour is wrong. Contour compensation after basic calibration. Arbitrary XY scaling.
Fit varies by material. Check profile and material shrinkage. One correction for all filaments.

A hole that is too small is not the same fault as a whole cube that is proportionally oversized in X and Y. Measure the kind of geometry error before compensating.

Wet filament can crackle, bubble, string, roughen surfaces and vary extrusion. PA/nylon and TPU are sensitive; PETG can deteriorate noticeably. A partly clogged or worn nozzle may still extrude, but inconsistently. If identical G-code suddenly prints badly after a new spool, investigate filament condition and profile before dismantling the printer.

Absorbed moisture can evaporate during melting and disrupt the material stream. PLA is generally more tolerant than PA/nylon or TPU, but not immune. A partial nozzle clog is deceptive because plastic still comes out. Depending on printer and hotend, a cold pull or nozzle inspection may help. Abrasive filaments can also wear the nozzle.

A generic material profile is a starting point, not a universal law. Even colours of the same brand can flow differently because of pigments. Matte PLA, silk PLA, PETG-HF and fibre-filled variants may require different Flow Ratio, temperature and MVS values.

P1S and Bambu Studio: quick diagnosis chart

Many Bambu Lab P1S machine functions are already automated. Focus on material-specific settings and keep a copy of a known good profile. Do not start with E-steps or firmware-like adjustments for an ordinary print-quality issue.

Problem First P1S/Bambu check Then
Stringing Dry filament and check material/nozzle temperature. Only then fine-tune retraction and travel.
Rough top surface Check Flow Ratio. Assess top-surface speed, line width and perhaps ironing.
Protruding corners or seam Check Flow Dynamics/K. Assess seam location, scarf seam or wipe.
Under-extrusion in fast infill Check MVS. Assess temperature, nozzle and material capacity.
Incorrect hole dimensions Targeted hole compensation. Validate CAD tolerance with a functional test.
Behaviour varies by spool Separate profile per material or variant. Document calibration values.

Do not immediately chase E-steps or firmware-style motor calibration on a normally functioning P1S. Do not use Flow Ratio to compensate for excessive MVS. Do not greatly increase retraction before checking dryness and temperature. Do not slow every movement when just one segment type fails, and do not overwrite a known good profile: make a copy for experiments.

You see Check first Then
Strings between features Dryness and temperature Retraction and travel.
Corners lift Plate, first layer, drafts Bed temperature, brim, enclosure.
Gaps between lines Nozzle, temperature, MVS Flow Ratio.
Bumps on one line Seam and Flow Dynamics/K Wipe or scarf seam.
Echo after a corner Mechanics and acceleration Input shaping and speed.
Sudden X/Y shift Obstruction, belts, plate Speed/acceleration as a test.
Sagging bridge Cooling and temperature Bridge speed/flow.
Rough overhang Cooling, temperature, orientation Overhang speed or support.
Holes too small Measure dimensions separately Hole compensation or CAD.
Problem only at high speed MVS and hotend capacity Temperature and speed.

Stop when the print reliably serves its purpose. A functional bracket may show layer lines; a display model may take longer. For printer-specific service procedures, the Prusa troubleshooting documentation and Bambu Lab Flow Rate guide remain useful references.

References and conclusion

For printer-specific procedures, follow manufacturer documentation. The source PDF also cites Prusa's layer-shifting guide alongside general troubleshooting and Bambu Flow Rate Calibration. Good troubleshooting is mainly about order: observe the symptom, check baseline conditions, test deliberately and change one variable at a time. That prevents a slicer profile becoming a collection of compensations.