Good calibration is not a pile of random test prints. The printer, build plate, nozzle and filament must be reliable first. Then come temperature, plastic quantity, pressure dynamics, maximum flow, dimensions, special geometry and a real validation print. Calibrate when solving a defect, using new material or deliberately improving speed and quality; a proven factory profile does not automatically need remeasurement.

A reliable baseline comes before temperature, flow and dimensions.

Why the order matters

One setting affects the next. Adjusting Flow Ratio with wet filament includes the moisture problem in the calibration. Measuring pressure advance during structural under-extrusion starts from a faulty baseline. Applying dimensional corrections while the first layer is swollen masks the wrong geometry. Keep printer factors such as belt tension, input shaping, bed levelling and mechanics separate from material/hotend values such as temperature, Flow Ratio, Flow Dynamics and Maximum Volumetric Speed (MVS).

The sequence is baseline → temperature → Flow Ratio → Flow Dynamics/K → MVS → dimensions → bridges and overhangs → real print. Change one variable per test and record the outcome.

This order prevents one wrong setting being compensated for with another. In practical terms, the recommended sequence means:

  1. Check hardware, build plate, nozzle and filament condition.
  2. Select a temperature range that gives good bonding, surface finish and overhangs.
  3. Use Flow Ratio to determine the correct amount of plastic for walls and surfaces.
  4. Use Flow Dynamics/pressure advance to compensate for pressure changes during acceleration and deceleration.
  5. Measure how many mm³/s the hotend-and-filament combination can melt reliably.
  6. Correct only the kind of dimensional error you actually measure.
  7. Only then optimise bridges, overhangs and cooling for special geometry.
  8. Validate the complete profile with a model resembling your real application.

Belt tension, input shaping, bed levelling, Z offset and mechanical inspection belong to the printer. Temperature, Flow Ratio, Flow Dynamics and MVS mainly depend on the material and hotend. A filament profile cannot repair a mechanical fault.

Step 0: establish a reliable baseline

Check that the nozzle is clean, not worn and the right diameter. The build plate should be clean, correctly selected and mounted flat. Belts, axes, toolhead and fans must not show mechanical defects. Filament must be dry and unwind freely; a partial clog or spool resistance makes measurements unreliable.

Start from a normal profile, for instance 0.20 mm layer height with a 0.4 mm nozzle if it fits your goal. Select a realistic temperature range around the manufacturer's value. Leave ironing, special seam strategies and extreme acceleration off initially. Save a known good profile before experimenting.

Component Check Why it comes first
Nozzle Clean, correct diameter and no visible wear. Extrusion and line width must be predictable.
Build plate Clean, correct plate type and mounted flat. First-layer errors must not distort the measurement.
Mechanics Belts, axes, toolhead and fans free of defects. Ringing and layer shifts are not flow problems.
Filament Dry, sufficient length and unwinding freely. Moisture and spool resistance make results unstable.
Profile Correct nozzle, layer height and material baseline. You need to test one variable at a time.

Step 1: choose a useful temperature

Temperature affects viscosity, layer bonding, gloss, stringing, bridges and melt capacity. The lowest string-free temperature is not necessarily best: functional parts may need more heat for bonding. Test a narrow sequence near the specified range at speeds representative of real prints. Judge layer bonding, overhangs, stringing, surface and corners together. A filament that prints well slowly at 210 °C may need a different thermal balance at higher volumetric flow.

On a temperature tower, check whether a segment breaks easily along layer lines, whether bridges and overhang edges stay sharp or sag, whether strands appear between separate features, and how gloss, matte finish, fine detail and line consistency change. Watch for build-up or oozing at corners. A cosmetically attractive segment may still have insufficient bonding for a functional part.

Work in four steps: choose a small range around the manufacturer or profile value; print the same geometry at successive temperatures; assess several properties, not just stringing; and record why the chosen temperature gives the best overall balance.

Step 2: set Flow Ratio

Flow Ratio or extrusion multiplier controls how much plastic is effectively deposited. Too low produces open top lines, thin walls and poor infill contact. Too high produces raised top surfaces, thick corners and possibly oversized outside dimensions. Use dry material at the selected temperature. Run a coarse and then, where available, a fine Flow Rate test. Choose closed surfaces and consistent lines, not one cosmetic detail; save the value in a separate filament profile. On a P1S this is the usual material-specific correction, not E-steps adjustment.

Flow too low Flow too high
Small gaps between top-surface lines. Ridges or excess plastic on the top surface.
Thin or weak walls. Outer dimensions may increase.
Infill does not join surrounding lines well. Corners and seams may thicken.
Sometimes a matte, under-extruded finish. The nozzle may drag surplus material.

For a reliable test, use dry filament at the temperature already selected. First find the approximate range, then perform a finer test if one is available. Decide from closed surfaces, consistent lines and dimensions. Do not disrupt the whole profile because of a single cosmetic detail. Save the result in a separate filament profile.

Step 3: calibrate Flow Dynamics/K

Melt pressure changes during acceleration and deceleration. Flow Dynamics or pressure advance (often K in Bambu terminology) compensates for it. Too little can thicken corners and pile material at speed changes; too much can make corners thin or pinched. Use a pattern with clear speed changes and select the most consistent lines. Test this after Flow Ratio because filament, temperature and extrusion system matter. Do not confuse it with retraction, which mainly affects travel without extrusion.

Too little compensation Too much compensation
Protruding or thickened corners. Thin or pinched corners.
Plastic accumulating at speed transitions. Under-extrusion after sharp changes in direction.
A more prominent seam. Overly aggressive start and stop behaviour.

Use a pattern with clear acceleration and deceleration. Do not automatically pick the highest or lowest K value: lines and corners should remain consistent across the pattern. Retraction is different; it mainly concerns travel moves without extrusion, although both mechanisms can affect a similar visible symptom.

Step 4: find MVS with a safety margin

MVS is the reliable melt capacity of hotend, nozzle and filament in mm³/s. Approximate volumetric demand is line width × layer height × print speed. A 0.48 mm wide, 0.20 mm high line at 200 mm/s demands about 19.2 mm³/s. At 0.45 × 0.16 × 200 it is 14.4 mm³/s; at 0.60 × 0.28 × 150 it is 25.2 mm³/s.

Start well below the expected limit, increase demand gradually and watch for deteriorating finish, line width or bonding. Choose a safety margin below that threshold. A reliable profile value of, for example, 20 mm³/s for eSUN PLA Basic on a P1S need not increase just because the printer can theoretically move faster. Stability beats a record value.

Line width Layer height Print speed Volumetric demand
0.45 mm 0.16 mm 200 mm/s 14.4 mm³/s
0.48 mm 0.20 mm 200 mm/s 19.2 mm³/s
0.60 mm 0.28 mm 150 mm/s 25.2 mm³/s

A taller or wider line therefore reaches the flow limit at a lower linear speed. Find the point where finish, line width or bonding deteriorates and set the working value below it. MVS is a limit of the hotend, nozzle and filament combination, not simply the advertised top speed of the machine.

Step 5: measure the right geometry

Correct dimensions only after extrusion and first layer are stable. After cooling, measure several positions with good calipers; one 20 mm cube says little about functional fit. Holes, pins, slots and a real bearing or bolt fit are more useful.

Measure more than one feature and measure each more than once. A warm print and material shrinkage affect dimensions. For a bearing holder, testing with the actual bearing tells you more than an arbitrary cube. If only a hole is too small, do not immediately change the whole outside contour. If only the first layer is wider, investigate that layer or use targeted elephant foot compensation.

Measured error Targeted first approach
All outer dimensions proportionally wrong Check printer, mechanics and profile; scale only for a sound reason.
Holes too small, outer dimensions fine Hole compensation or CAD tolerance.
Outer contour slightly large or small Contour compensation after baseline checks.
Only bottom layers too wide First-layer work or elephant foot compensation.

Step 6: bridges and overhangs

These special cases come after basic flow and temperature. A bridge needs a line tensioned enough to span the gap: cooling, temperature, bridge speed and bridge flow act together. More cooling often helps PLA or PETG but may harm ABS/ASA layer bonding. Overhangs depend on layer height, cooling, minimum layer time and orientation; slower is not always better if plastic stays hot longer. Calibrate for shapes you actually print, not an extreme test model irrelevant to your work.

Bridges

  • More cooling often helps PLA and PETG, but may weaken ABS/ASA layer bonding.
  • Excessive heat makes plastic sag more easily; too little heat can reduce bonding or cause a bridge line to break.
  • A suitable bridge speed tensions the line without outrunning extrusion.
  • Lower bridge flow may help if lines sag under their own weight, but test it deliberately.

Overhangs

  • A smaller layer height reduces the horizontal step of each successive layer.
  • Slower is not always better: material may stay hot longer. Cooling and minimum layer time also matter.
  • Reorienting the model or changing its design is often more effective than extreme slicer values.

The aim is a profile that improves your actual work. If you seldom print long bridges, there is no need to optimise for a 100 mm bridge test.

Step 7: validate with a real print

Choose a representative model with straight walls, corners, a top surface, a hole or fit, a short bridge or overhang, and both short and long segments. Judge surface, dimensions, layer bonding, speed and repeatability. A profile that prints spectacularly once but inconsistently later is less useful than a conservative profile that repeats the result twenty times.

Include a feature you often print, such as a snap-fit, screw hole or thin wall. Then check each category separately:

Category Question for the real print
Surface Are the top, walls and seam acceptable?
Dimensions Do holes, pins and outer dimensions fit?
Strength Does the part avoid breaking unusually easily along layer lines?
Speed Is quality stable in faster sections?
Repeatability Does a second print give the same result?

For Bambu Lab P1S and Bambu Studio: copy the generic or manufacturer profile under a clear name such as eSUN PLA Basic - P1S - 0.4; dry the material; calibrate Flow Ratio and K; test MVS when high speed or under-extrusion justifies it. Only then adjust process settings such as walls, infill, seam, support and top surface. Keep brand, variant, nozzle and possibly colour with the profile name. For individual slicer controls, see Bambu Studio: every important setting explained.

Which setting belongs in which profile?

Parameter Primarily belongs to
Nozzle and bed temperature Filament profile.
Flow Ratio Filament profile.
Flow Dynamics/K Filament or saved calibration value.
Maximum Volumetric Speed Filament profile.
Layer height, walls and infill Process profile.
Support, seam and ironing Process profile or model goal.
Printer and nozzle type Printer profile.

Do not make one 'magic profile' for every material and colour. Save a clearly named copy, dry the filament, start at the standard temperature, calibrate Flow Ratio and K, and test MVS only when speed or under-extrusion provides a reason. Adjust process values afterwards. Document brand, material, variant, nozzle and, if relevant, colour so you still know what the saved values apply to.

When should you recalibrate?

A new spool of exactly the same filament often only needs visual validation. With a different colour or variant, check Flow Ratio/K if behaviour changes. A new brand or material calls for temperature, Flow Ratio, Flow Dynamics and MVS; another nozzle diameter also affects process profile and dimensions. After a major firmware or slicer update, compare prints first; after mechanical repair, recheck the printer baseline.

Change What should be checked again?
New spool of exactly the same filament Visual validation; recalibrate only if the result differs.
Another colour or variant Flow Ratio and Flow Dynamics if behaviour changes.
New brand or material Temperature, Flow Ratio, Flow Dynamics and MVS.
New nozzle of the same diameter Short validation; MVS if hotend or nozzle material changed.
Another nozzle diameter Temperature behaviour, flow/MVS, process profile and dimensions.
Major firmware or slicer update Compare prints first; recalibrate only if the result changed.
Mechanical repair Printer baseline, dimensions and a real validation print.

Recalibration is worthwhile if top surfaces no longer close as before, corners become visibly thick or thin, fast infill or walls show under-extrusion, functional fits change while the CAD model remains the same, or a new material behaves clearly differently from its generic profile.

Log date, filament, nozzle, temperature, Flow Ratio, K, MVS and result for each test. A profile is done when it reliably serves its purpose, not when every parameter seems optimised to three decimals. For current UI names and procedures, consult the Bambu Lab Flow Rate guide and your printer's documentation.

Quick reference and calibration log

Step Goal Stop criterion
0. Baseline Stable printer and material. No obvious hardware or moisture fault.
1. Temperature Balance bonding, surface and overhangs. One useful temperature range selected.
2. Flow Ratio Correct quantity of plastic. Top and walls close without excess material.
3. Flow Dynamics Consistent extrusion through speed changes. Clean corners without thinning.
4. MVS Reliable maximum flow. Safety margin below the visible quality limit.
5. Dimensions Targeted dimensions and fit. Test features suit the application.
6. Bridges and overhangs Special geometry. Sufficient quality for real models.
7. Validation Test everything together. Repeatable, representative result.

A simple log has date, filament, nozzle, temperature in °C, Flow Ratio, K, MVS and a note on each row. Add a row for every test. Later you can still tell why the profile has those values. Calibration is complete when the profile reliably meets its goal, not when every parameter has been 'optimised' to three decimal places.

Sources and further reading

Interfaces and button names can change after updates. Check printer-specific procedures in current manufacturer and slicer documentation. The source PDF points to Bambu Lab Flow Rate Calibration, Bambu Lab Community/Bambu Studio documentation about Flow Dynamics and filament calibration, and the Prusa Knowledge Base on print quality. The technical sequence remains: baseline → temperature → Flow Ratio → Flow Dynamics → MVS → dimensions → bridges/overhangs → real validation.